View MSM82C54-2_39503.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
E2O0019-27-X2
Semiconductor MSM82C54-2RS/GS/JS
Semiconductor CMOS PROGRAMMABLE INTERVAL TIMER
This version: Jan. 1998 MSM82C54-2RS/GS/JS Previous version: Aug. 1996
GENERAL DESCRIPTION
The MSM82C54-2RS/GS/JS is a programmable universal timer designed for use in microcomputer systems. Based on silicon gate CMOS technology, it requires a standby current of only 10 mA (max.) when the chip is in the non-selected state. And during timer operation, the power consumption is still very low with only 10mA (max.) of current required. It consists of three independent counters, and can count up to a maximum of 10 MHz. The timer features six different counter modes, and binary count/BCD count functions. Count values can be set in byte or word units, and all functions are freely programmable.
FEATURES
* Maximum operating frequency of 10 MHz (VCC=5 V) * High speed and low power consumption achieved by silicon gate CMOS technology * Completely static operation * Three independent 16-bit down-counters * Status Read Back Command * Six counter modes available for each counter * Binary and decimal counting possible * 24-pin Plastic DIP (DIP24-P-600-2.54): (Product name: MSM82C54-2RS) * 28-pin Plastic QFJ (QFJ28-P-S450-1.27): (Product name: MSM82C54-2JS) * 32-pin Plastic SSOP (SSOP32-P-430-1.00-K): (Product name: MSM82C54-2GS-K)
1/23
Semiconductor
MSM82C54-2RS/GS/JS
FUNCTIONAL BLOCK DIAGRAM
VCC GND 8 D7 - D0 Data Bus Buffer
Counter #0
CLK0 GATE0 OUT0
8 WR RD A0 A1 CS
Read/ Write Logic
Counter #1
CLK1 GATE1 OUT1
Control Word Register
Counter #2
CLK2 GATE2 OUT2
Internal Bus
2/23
Semiconductor
MSM82C54-2RS/GS/JS
PIN CONFIGURATION (TOP VIEW)
24 pin Plastic DIP
D7 1 D6 2 D5 3 D4 4 D3 5 D2 6 D1 7 D0 8 CLK0 9 OUT0 10 GATE0 11 GND 12 24 Vcc 23 WR 22 RD 21 CS 20 A1 19 A0 18 CLK2 17 OUT2 16 GATE2 15 CLK1 14 GATE1 13 OUT1
32 pin Plastic SSOP
NC D7 D6 D5 NC D4 D3 D2 D1 D0 CLK0 NC OUT0 GATE0 GND NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
NC Vcc WR RD NC CS A1 A0 CLK2 OUT2 GATE2 NC CLK1 GATE1 OUT1 NC
27 WR
28 VCC
28 pin Plastic QFJ
D4 5 D3 6 D2 7 D1 8 D0 9 CLK0 10 NC 11
OUT0 12 GATE0 13 GND 14 NC 15 OUT1 16 GATE1 17 CLK1 18
26 RD
1 NC
4 D5
3 D6
2 D7
25 NC 24 CS 23 A1 22 A0 21 CLK2 20 OUT2 19 GATE2
(NC denotes "not connected".)
3/23
Semiconductor
MSM82C54-2RS/GS/JS
ABSOLUTE MAXIMUM RATING
Parameter Power Supply Voltage Input Voltage Output Voltage Storage Temperature Power Dissipation Symbol VCC VIN VOUT TSTG PD Condition With respect to GND -- Ta = 25C 0.9 Rating
MSM82C54-2RS MSM82C54-2GS MSM82C54-2JS
Unit V V V C 0.9 W
-0.5 to +7 -0.5 to VCC +0.5 -0.5 to VCC +0.5 -55 to +150 0.7
RECOMMENDED OPERATING CONDITIONS
Parameter Power Supply Voltage Operating Temperature "L" Input Voltage "H" Input Voltage Symbol VCC Top VIL VIH Min. 4.5 -40 -0.5 2.2 Typ. 5 +25 -- -- Max. 5.5 +85 +0.8 VCC + 0.5 Unit V C V V
DC CHARACTERISTICS
Parameter "L" Output Voltage "H" Output Voltage Input Leak Current Output Leak Current Standby Supply Current Operating Supply Curent Symbol VOL VOH ILI ILO ICCS Conditions IOL = 2.5 mA IOH = -2.5 mA IOH = -100 mA 0 VIN VCC 0 VOUT VCC cs VCC -0.2 V VIH VCC -0.2 V VIH 0.2 V tCLK =100 ns, CL = O pF VCC = 4.5 V to 5.5 V Ta = -40C to +85C Min. -- 3.0 VCC -0.4 -10 -10 -- Typ. -- -- -- -- -- -- Max. 0.4 -- -- 10 10 10 Unit V V V mA mA mA
ICC
--
--
10
mA
4/23
Semiconductor
MSM82C54-2RS/GS/JS
AC CHARACTERISTICS
(VCC = 4.5 V to 5.5 V, Ta = -40C to +85C) Parameter Address Set-up Times to Falling Edge of RD Chip Select Input Set-up Time to Falling Edge of RD Address Hold Time from Rising Edge of RD RD Pulse Width Data Access Time from Falling Edge of RD Data Access Time after Address Determination Delay Time from Rising Edge of RD to Data Floting State RD Recovery Time Address Set-up Time to Falling Edge of WR Chip Select Input Set-up Time to Falling Edge of WR Address Hold Time from Rising Edge of WR WR Pulse Width Data Determination Set-up Time to Rising Edge of WR Data Hold Time after Rising Edge of WR WR Recovery Time CLK Cycle Time CLK "H" Level Width CLK "L" Level Width CLK Rise Time CLK Fall Time GATE "H" Level Width GATE "L" Level Width GATE Input Set-up Time before Rising Edge of CLK GATE Input Hold Time before Rising Edge of CLK Output Delay Time after Falling Edge of CLK Output Delay Time after Falling Edge of GATE CLK Rise Delay Time after Rising Edge of WR for Count Value Loading GATE sampling delay time after rising edge of WR for count loading Output Delay Time after Falling Edge of WR for Mode Set CLK Fall Set-up Time to Falling Edge of WR for Counter Latch Command Symbol tAR tSR tRA tRR tRD tAD tDF tRV tAW tSW tWA tWW tDW tWD tRV tCLK tPWH tPWL tr tf tGW tGL tGS tGH tOD tODG tWC tWG tWO tCL 82C54-2 Min. 30 0 0 95 -- -- 5 165 0 0 0 95 85 0 165 100 30 50 -- -- 50 50 40 50 -- -- 0 -5 -- -40 Max. -- -- -- -- 94 184 65 -- -- -- -- -- -- -- -- D.C. -- -- 25 25 -- -- -- -- 100 100 55 40 240 40 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns CL = 150 pF Conditions
Note:
Timing measured at VL = 0.8 V and VH = 2.2 V for both inputs and outputs.
Clock Gate Timing
Write Timing
Read Timing
ns
5/23
Semiconductor
MSM82C54-2RS/GS/JS
TIMING CHART
WriteTiming
A0 - 1
tAW
tWA
CS
tSW
D0 - 7 tDW WR tWW tWD
Read Timing
A0 - 1 tAR CS tSR RD tRD D0 - 7 tAD tRR tDF Valid tRA
Recovery Timing
tRV RD, WR
Clock & Gate Timing
WR Mode Count tWC tPWH CLK tf GATE tPWL tWO OUT tr tWG tGH tGS tGL tODG tOD tGW tGH tCLK tGS
Counter Latch
tCL
6/23
Semiconductor
MSM82C54-2RS/GS/JS
DESCRIPTION OF PIN FUNCTIONS
Pin Symbol Name Bidirectional Data Bus Input/Output Function Three-state 8-bit bidirectional data bus used when writing control words and count value, and reading count values upon reception of WR and RD signals from CPU. Data transfer with the CPU is enabled when this pin is at low level. When at high level, the data bus (D0 thru D7) is switched to high impedance state where neither writing nor reading can be executed. Internal registers, however, remain unchanged. Data can be transferred from MSM82C54-2 to CPU when this pin is at low level. Data can be transferred from CPU to MSM82C54-2 when this pin is at low level. One of the three internal counters or the control word register is selected by A0/A1 combination. These two pins are normally connected to the two lower order bits of the address bus. Supply of three clock signals to the three counters incorporated in MSM82C54-2. Control of starting, interruption, and restarting of counting in the three respective counters in accordance with the set control word contents. Output of counter output wave form in accordance with the set mode and count value.
D7 - D0
Input/Output
CS
Chip Select Input
Input
RD WR
Read Input Write Input
Input Input
A0, A1
Address Input
Input
CLK0 - 2
Clock Input
Input
GATE0 - 2
Gate Input
Input
OUT0 - 2
Counter Output
Output
SYSTEM INTERFACING
Adress Bus A1 A0 Control Bus 16 bits
Data Bus 8 bits
8 bits
A1 A0
CS
RD D7 - 0 MSM82C54-2
Counter #1
OUT GATE CLK
WR
Counter #0
OUT GATE CLK
Counter #2
OUT GATE CLK
7/23
Semiconductor
MSM82C54-2RS/GS/JS
DESCRIPTION OF BASIC OPERATIONS
Data transfers between the internal registers and external data bus is outlined in the following table.
CS 0 0 0 0 0 0 0 0 1 0 RD 1 1 1 1 0 0 0 0 1 WR 0 0 0 0 1 1 1 1 1 A1 0 0 1 1 0 0 1 1 A0 0 1 0 1 0 1 0 1 Data Bus in High Impedance Status Function Data Bus to Counter #0 Writing Data Bus to Counter #1 Writing Data Bus to Counter #2 Writing Data Bus to Control Word Register Writing Data Bus from Counter #0 Writing Data Bus from Counter #1 Writing Data Bus from Counter #2 Writing
: denotes "not specified"
DESCRIPTION OF OPERATION
MSM82C54-2 functions are selected by control words from the CPU. In the required program sequence, the control word setting is followed by the count value setting and execution of the desired timer operation.
Control Word and Count Value Program Each counter operating mode is set by control word programming. The control word format is outlined below.
D7 SC1 D6 SC0 D5 RL1 D4 RL0 D3 M2 D2 M1 Mode D1 M0 D0 BCD BCD
Select Counter
Read/Load
(CS=0, A0, A1=1, 1, RD=1, WR=0)
8/23
Semiconductor * Select Counter (SC0, SC1): Selection of set counter
SC1 0 0 1 1 SC0 0 1 0 1 Counter #0 selection Counter #1 selection Counter #2 selection Read Back Command Set Contents
MSM82C54-2RS/GS/JS
* Read/Load (RL1, RL0): Count value Reading/Loading format setting
RL1 0 0 1 1 RL0 0 1 0 1 Counter Latch Operation Reading/Loading of Least Significant Byte (LSB) Reading/Loading of Most Significant Byte (MSB) Reading/Loading of LSB followed by MSB Set Contents
* Mode (M2, M1, M0): Operation waveform mode setting
M2 0 0 1 1 M1 0 0 1 1 0 0 M0 0 1 0 1 0 1 Set Contents Mode 0 (Interruput on Terminal Count) Mode 1 (Programmable One-Shot) Mode 2 (Rate Generator) Mode 3 (Square Wave Generator) Mode 4 (Software Triggered Strobe) Mode 5 (Hardware Triggered Strobe)
: denotes "not specified"
* BCD: Operation count mode setting
BCD 0 1 Binary Count (16-bit Binary) BCD Count (4-decade Binary Coded Decimal) Set Contents
After setting Read/Load, Mode and BCD in each counter as outlined above, next set the desired count value. (In some Modes, the count value is set first. In next clock, loading is performed, then counting starts.) This count value setting must conform with the Read/Load format set in advance. Note that the internal counters are reset to 0000H during control word setting. The counter value (0000H) can't be read. The program sequence of the MSM82C54-2 is flexible. Free sequence programming is possible as long as the two following rules are observed: (i) Write the control word before writing the initial count value in each counter. (ii) Write the initial count value according to the count value read/write format specified by the control word. Note: Unlike the MSM82C53-2, the MSM82C54-2 allows count value setting for another counter between LSB and MSB settings.
9/23
Semiconductor
MSM82C54-2RS/GS/JS
* Example of control word and count value setting
Counter #0: Read/Load LSB only, Mode 3, Binaty count, count value 3H Counter #1: Read/Load MSB only, Mode 5, Binaty count, count value AA00H Counter #2: Read/Load LSB and MSB, Mode 0, BCD count, count value 1234
MVI A, 1EH OUT n3 MVI A, 6AH OUT n3 MVI A, B1H OUT n3 MVI A, 03H OUT n0 MVI A, AAH OUT n1 MVI A, 34H OUT n2 MVI A, 12H OUT n2
Counter #0 control word setting
Counter #1 control word setting
Counter #2 control word setting
Counter #0 count value setting
Counter #1 count value setting
Counter #2 count value setting (LSB then MSB)
Notes: n0: Counter #0 address n1: Counter #1 address n2: Counter #2 address n3: Control word register address
* The minimum and maximum count values which can be counted in each mode are listed below.
Mode 0 1 2 3 4 5 MIn. 1 1 2 2 1 1 Max. 0 0 0 0 0 0 -- 1 cannot be counted 1 cannot be counted -- -- Remarks 0 executes 10000H count (ditto in other mdoes)
10/23
Semiconductor Internal Block Diagram of a Counter
MSM82C54-2RS/GS/JS
Internal Data Bus Control Word Register
Status Latch CRM Status Register CRL
Control Logic
CE
OLM
OLL
GATEn CLKn OUTn NOTE : CRM : CRL : CE : OLM : OLL : Count Register MSB Count Register LSB Counter Element Output Latch MSB Output Latch LSB
11/23
Semiconductor Mode definition Mode 0
MSM82C54-2RS/GS/JS
* Application: Event counter * Output operation: The output is set to "L" level by the control word setting, and kept at "L" level until the counter value becomes 0. * Gate function: "H" level validates the count operation, and "L" level invalidates it. The gate does not affect the output. * Count value load timing: after the control word and initial count value are written, the count value is loaded to the CE at the falling edge of the next clock pulse. The first clock pulse does not cause the count value to be decremented. In other words, if the initial count value is N, the output is not set to "H" level until the input of (N+1) the clock pulse after the initial count value writing. * Count value writing during counting: The count value is loaded in the CE at the falling edge of the next clock, and counting with the new count value continues. The operation for 2-byte count is as follows: 1) The counting operation is suspended when the first byte is written. The output is immediately set to "L" level. (no clock pulse is required.) 2) After the second byte is written, the new count value is loaded to the CE at the falling edge of the next clock. For the output to go to "H" level again, N+1 clock pulse are necessary after new count value N is written. * Count value writing when the gate signal is "L" level: The count value is also loaded to the CE at the falling edge of the next clock pulse in this case. When the gate signal is set to "H" level, the output is set to "H" level after the lapse of N clock pulses. Since the count value is already loaded in the CE, no clock pulse for loading in the CE is necessary.
Mode 1 * Application: Digital one-shot * Output operation: The output is set to "H" level by the control word setting. It is set to "L" level at the falling edge of the clock succeeding the gate trigger, and kept at "L" level until the counter value becomes 0. Once the output is set to "H" level, it is kept at "H" level until the clock pulse succeeding the next trigger pulse. * Count value load timing: After the control word and initial count value are written, the count value is loaded to the CE at the falling edge of the clock pulse succeeding the gate trigger and set the output to "L" level. The one-shot pulse starts in this way. If the initial count value is N, the one-shot pulse interval equals N clock pulses. The one-shot pulse is not repetitive. * Gate function: The gate signal setting to "L" level after the gate trigger does not affect the output. When it is set to "H" level again from "L" level, gate retriggering occurs, the CR count value is loaded again, and counting continues. * Count value writing during counting It does not affect the one-shot pulse being counted until retriggering occurs.
12/23
Semiconductor Mode 2
MSM82C54-2RS/GS/JS
* Application: Rate generator, real-time interrupt clock. * Output operation: The output is set to "H" level by control word setting. When the initial count value is decremented to 1, the output is set to "L" level during one clock pulse, and is then set to "H" level again. The initial count value is reloaded, and the above sequence repeats. In mode 2, the same sequence is repeated at intervals of N clock pulses if the initial count value is N for example. * Gate function: "H" level validates counting, and "L" level invalidates it. If the gate signal is set to "L" level when the output pulse is "L" level, the output is immediately set to "H" level. At the falling edge of the clock pulse succeeding the trigger, the count value is reloaded and counting starts. The gate input can be used for counter synchronization in this way. * Count value load timing: After the control word and initial count value is written, the count value is loaded to the CE at the falling edge of the next clock pulse. The output is set to "L" level upon lapse of N clock pulses after writing the initial count value N. Counter synchronization By software is possible in this way. * Count value writing during counting: Count value writing does not affect the current counting operation sequence. If new count value writing completes and the gate trigger arrives before the end of current counting operation, the count value is loaded to the CE at the falling edge of next clock pulse and counting continues from the new count value. If no gate trigger arrives, the new count value is loaded to the CE at the end of the current counting operation cycle. In mode 2, count value of 1 is prohibited.
Mode 3 * Application: Baud rate generator, square wave generator * Output operation: Same as mode 2 except that the output duty is different. The output is set to "H" level by control word setting. When the count becomes half the initial count value, the output is set to "L" level and kept at "L" level during the remainder of the count. Mode 3 repeats the above sequence periodically. If the initial count value is N, the output becomes a square wave with a period of N. * Gate operation: "H" level validates counting, and "L" level invalidates it. If the gate signal is set to "L" level when the output is "L" level, the output is immediately set to "H" level. The initial count value is reloaded at the falling edge of the clock pulse succeeding the next gate trigger. The gate can be used for counter synchronization in this way. * Count value load timing: After the control word and initial count value are written, the count value is loaded to the CE at the falling edge of the next clock pulse, Counter synchronization by software is possible in this way. * Count value writing during counting: The count value writing does not affect the current counting operation. When the gate trigger input arrives before the end of a half cycle of the square wave after writing the new count value, the new count value is loaded in the CE at the falling edge of the next clock pulse, and counting continues using the new count value. If there is no gate trigger, the new count value is loaded at the end of the half cycle and counting continues. * Even number counting operation: The output is initially set to "H" level. The initial count value is loaded to the CE at the falling edge of the next clock pulse, and is decremented by 2 by consecutive clock pulses. When the counter value becomes 2, the output is set to "L" level, the initial value is reloaded and then the above operation is repeated. 13/23
Semiconductor
MSM82C54-2RS/GS/JS
* Odd number counting operation: The output is initially set to "H" level. At the falling edge of the next clock pulse, the initial count value minus one is loaded in the CE, and then the value is decremented by 2 by consecutive clock pulses. When the counter value becomes 0, the output is set to "L" level, and then the initial count value minus 1 is reloaded to the CE. The value is then decremented by 2 by consecutive clock pulses. When the counter value becomes 2, the output is again set to "H" level and the initial count value minus 1 is again reloaded. The above operations are repeated. In other words, the output is set to "H" level during (N+1)/2 counting and to "L" level during (N-1)/2 counting in the case of odd number counting.
Mode 4 * Application: Software trigger strobe * Output operation: The output is initially set to "H" level. When the counter value becomes 0, the output goes to "L" level during one clock pulse, and then restores "H" level again. The count sequence starts when the initial count value is written. * Gate function: "H" level validates counting, and "L" level invalidates counting. The gate signal does not affect the output. * Count value load timing: After the control word and initial count value are written, the count value is loaded to the CE at the falling edge of the next clock pulse. The clock pulse does not decrement the initial count value. If the initial count value is N, the strobe is not output unless N+1 clock pulses are input after the initial count value is written, * Count value writing during counting: The new count value is written to the CE at the falling edge of the next clock pulse, and counting continues using the new count value. The operation for 2-byte count is as follows: 1) First byte writing does not affect the counting operation. 2) After the second byte is written, the new count value is loaded to the CE at the falling edge of the next clock pulse. This means that the counting operation is retriggered by software. The output strobe is set to "L" level upon input of N+1 clock pulses after the new count value N is written.
Mode 5 * Application: Hardware trigger strobe * Output operation: The output is initially set to "H" level. When the counter value becomes 0 after triggering by the rising edge of the gate pulse, the output goes to "L" level during one clock pulse, and then restores "H" level. * Count value load timing: Even after the control word and initial count value are written, loading to the CE does not occur until the input of the clock pulse succeeding the trigger. For the clock pulse for CE loading, the count value is not decremented. If the initial count value is N, therefore, the output is not set to "L" level until N+1 clock pulses are input after triggering. * Gate function: The initial count value is loaded to the CE at the falling edge of the clock pulse succeeding gate triggering. The count sequence can be retriggered. The gate pulse does not affect the output.
14/23
Semiconductor
MSM82C54-2RS/GS/JS
* Count value writing during counting: The count value writing does not affect the current counting sequence. If the gate trigger is generated after the new count value is written and before the current counting ends, the new count value is loaded to the CE at the falling edge of the next clock pulse, and counting continues using the new count value. The various roles of the gate input signals in the above modes are summarized in the following table.
Gate Mode 0 1 2 3 4 5 (1) Counting not possible (2) Counter output forced to "H" level (1) Counting not possible (2) Counter output forced to "H" level Counting not possible (1) Start of counting (2) Retriggering
"L" Level Falling Edge Counting not possible
Rising Edge
"H" Level Counting possible
(1) Start of counting (2) Retriggering Start of counting Start of counting Counting possible Counting possible Counting possible
15/23
Semiconductor
MSM82C54-2RS/GS/JS
Mode 0
CLK WR OUT (n=4) (GATE = "H") 4 3 2 1 0 (n=2) 2 1 0
WR (n=4) GATE OUT 4 3 2 1 0
Mode 1
CLK WR (n=4) GATE OUT GATE OUT (n=4) 4 3 2 4 3 2 1 0 4 3 2 1 0
Mode 2
CLK WR OUT GATE 4 OUT (n=4) 3 2 1 4 4 3 2 1 (n=4) 4 (GATE = "H") 3 2 1 (n=2) 4 3 2 1 2 1 2
Mode 3
CLK WR OUT GATE OUT (n=5) (n=4) 4 (GATE = "H") 4 2 0 4 2 4 2 0 4 2 4 2 2 4 2 4 2 (n=3) 4 2 3 2 3 3
Mode 4
CLK WR OUT GATE 4 OUT 3 2 1 0 4 (GATE = "H") 3 2 1 0
Mode 5
CLK GATE 4 OUT GATE 4 OUT (n=4) 3 2 1 4 3 2 1 0 (n=4) 3 2 1 0
Note : "n" is the value set in the counter. Figures in these diagrams refer to counter values.
16/23
Semiconductor Reading Counter Values
MSM82C54-2RS/GS/JS
All MSM82C54-2 counting is down-counting, the counting being in steps of 2 in mode 3. Counter values can be read during counting by. (1) direct reading, (2) counter latching ("read on the fly"), and (3) read back command.
(1) Direct reading Counter values can be read by direct reading operations. Since the counter value read according to the timing of the RD and CLK signals is not guaranteed, it is necessary to stop the counting by a gate input signal, or to interrupt the clock input temporarily by an external circuit to ensure that the counter value is correctly read. (2) Counter latching In this method, the counter value is latched by writing counter latch command, thereby enabling a stable value to be read without effecting the counting in any way at all. The output latch (OL) of the selected counter latches the count value when a counter latch command is written. The count value is held until it is read by the CPU or the control word is set again. If a counter latch command is written again before reading while a certain counter is latched, the second counter latch command is ignored and the value latched by the first counter latch command is maintained. The MSM82C54-2 features independent reading and writing from and to the same counter. When a counter is programmed for the 2-byte counter value, the following sequence is possible: 1. Count value (LSB) reading 2. New count value (LSB) writing 3. Count value (MSB) reading 4. New count value (MSB) writing An example of a counter latching program is given below. Counter latching executed for counter #1 (Read/Load 2-byte setting)
MVI A 0100 Denotes counter latching OUT n3 Write in control word address (n3) The counter value at this point is latching IN n1 Reading of the LSB of the counter value latched from counter #1. n1: Conter #1 address MOV B, A IN n1 MOV C, A Reading of MSB from counter #1
17/23
Semiconductor
MSM82C54-2RS/GS/JS
(3) Read Back Command Operation Use of the read back command enables the user to check the count value, program mode, output pin state and null count flag of the selected counter. The command is written in the control word register, and the format is as shown below. For this command, the counter selection occurs according to bits D3, D2 and D1.
D7 1 D6 1 D5 COUNT D4 STATUS D3 CNT2 D2 CNT1 D1 CNT0 D0 0
(CS=0, A0, A1=1, RD=1, WR=0) D5: 0 = Selected counter latch operation D4: 0 = Selected counter status latch operation D3: 1 = Counter #2 selection D2: 1 = Counter #1 selection D1: 1 = Counter #0 selection D0: 0 = Fixed
It is possible to latch multiple counters by using the read back command. Latching of a read counter is automatically canceled but other counters are kept latched. If multiple read back commands are written for the same counter, commands other than the first one are ignored. It is also possible to latch the status information of each counter by using the read back command. The status of a certain counter is read when the counter is read. The counter status format is as follows: Bits D5 to D0 indicate the mode programmed by the most recently written control word. Bit D7 indicates the status of the output pin. Use of this bit makes it possible to monitor the counter output, so the corresponding hardware may be omitted.
D7
D6
D5 RL1
D4 RL0
D3 M2
D2 M1
D1 M0
D0 BCD
NULL OUTPUT COUNT
D7: 1 = Output pin status is 1. 0 = Output pin status is 0. D6: 1 = Null count 0 = Count value reading is effective D5 - D0: Programmed mode of counter (See the control word format.)
18/23
Semiconductor
MSM82C54-2RS/GS/JS
Null count indicates the count value finally written in the counter register (CR) has been loaded in the counter element (CE). The time when the count value was loaded in the CE depends on the mode of each counter, and it cannot be known by reading the counter value because the count value does not tell the new count value if the counter is latched. The null count operation is shown below. Operation A. Control word register writing B. Count register (CR) writing C. New count loading to CE (CRAECE) Result Null count = 1 Null count = 1 Null count = 0
Note: The null count operation for each counter is independent. When the 2-byte count is programmed, the null count is set to 1 when the count value of the second byte is written. If status latching is carried out multiple times before status reading, other than the first status latch is ignored. Simultaneous latching of the count and status of the selected counter is also possible. For this purpose, set bits D4 and D3, COUNT and STATUS bits, to 00. This is functionally the same as writing two separate read back commands at the same time. If counter/status latching is carried out multiple times before each reading, other than the first one is ignored here again. The example is shown below.
Command
D7 D6 D5 D4 D3 D2 D1 D0
Contents
Counter 0
Counter 1
Counter 2
Count Status Count Status Count Status
1 1 1 1 1 1
1 1 1 1 1 1
0 1 1 0 0 1
0 0 0 1 0 0
0 0 1 1 0 0
0 1 1 0 1 0
1 0 0 0 0 1
Read back status and count 0 (counter 0) 0 Read back status (counter 1) 0 Read back status (counter 1 and 2) 0 Read back status (counter 2) 0 Read back status and count (counter 1)
L L L L L L
L L L L L
(NOTE)
-- -- -- -- L L
-- L L
(NOTE)
-- -- -- L L L
-- -- L L L L
L L
(NOTE)
0 Read back status (counter 0)
L
L
Note:
The latch command at this time point is ignored, and the first latch command is valid.
If both the count and status are latched, the status latched in the first counter read operation is read. The order of count latching and status latching is irrelevant. The count(s) of the next one or two reading operations is or are read. Note: There is the possibility of glitch noise in the output low level when reading out the data. Peak voltage in typical condition (5 V, 25C) is approximately 1V and in the worst condition (5.5 V, -40C) is approximately 1.4V.
19/23
Semiconductor Example of Practical Application * MSM82C54-2 used as a 32-bit counter.
MSM82C54-2RS/GS/JS
MSM82C54 -2 CLK0 CLK1 CLK2 OUT0 OUT1 OUT2
Use counter #1 and counter #2 Counter #1: mode 0, upper order 16-bit counter value Counter #2: mode 2, lower order 16-bit counter value This setting enables counting up to a maximum of 232.
20/23
Semiconductor
MSM82C54-2RS/GS/JS
PACKAGE DIMENSIONS
(Unit : mm)
DIP24-P-600-2.54
Package material Lead frame material Pin treatment Solder plate thickness Package weight (g)
Epoxy resin 42 alloy Solder plating 5 mm or more 3.55 TYP.
Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki's responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times).
21/23
Semiconductor
MSM82C54-2RS/GS/JS
(Unit : mm)
QFJ28-P-S450-1.27
Spherical surface
Package material Lead frame material Pin treatment Solder plate thickness Package weight (g)
Epoxy resin Cu alloy Solder plating 5 mm or more 1.00 TYP.
Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki's responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times).
22/23
Semiconductor
MSM82C54-2RS/GS/JS
(Unit : mm)
SSOP32-P-430-1.00-K
Mirror finish
Package material Lead frame material Pin treatment Solder plate thickness Package weight (g)
Epoxy resin 42 alloy Solder plating 5 mm or more 0.60 TYP.
Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki's responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times).
23/23

▲Up To Search▲

Price & Availability of MSM82C54-2

	To Download MSM82C54-2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .